RUXIFEY Sequential LED Side Mirror Reflector Lights Smoked Lens Compatible with Ford F150 2009 to 2014

People complain about not lasting very long. I went and put a small layer of clear 20 year caulk around the area you can't see. There is a small line that I think let's water in so I sealed that area. Let it dry more than two days before installing. Knock on wood I haven't had any problems.

Bought these for my f150 and they were very bright and well made! Would definitely buy again! Plus looked really good!!

I paired these indicators with the rear facing sequential indicators on a 2011 F150. Installation was fairly straight forward and connections are as the instructions and other reviews indicated. However, if you plan to run the wire(s) for running lights, I recommend just remove the door panel and the three nuts holding the mirror on and remove the mirror from the truck. It takes probably 3 minutes with a 6, 8 and 11mm socket, a t20 bit, and hook to pop cover panels on the door panel. This also affords you the opportunity to most delicately remove the mirror from the internal mount (it just snaps on in 4 paired clips at 2,4,8,10 o’clock positions behind the mirror). If you are like me, I cleaned inside the mirror body, behind the mirror on the door and most importantly I was able to easily drop the running light wire(s) into the wire channel and pull through. It helped to firmly pull the end of the running wire through my fingers to straighten with a slight curve and feed through the wire channel and then tilt the mirror on its mounting end and the wire just dropped out or was within grasp to help pull it through. Once ran, fold excess running light wire back up, reuse the wire tie and when remounting mirror feed through door channel with the mirror electrical connector. Once remounted you can feed the wires inside the kick panel through the door rubber electrical grommet. You don’t ‘have’ to remove the mirror to mount these but I found it less time consuming and frustrating because the wire would bunch up and my fish tape was too big/stiff to make the 90 deg bend in the mirror body when it was mounted. All in all 10min per mirror start to finish with cleaning and even using McGuire’s black plastic restore on the mirror plastics.

These fit right in on my 2014 F150 mirrors. The mirrors were slightly difficult to take apart, but once apart, these went right in. Nice and bright I like them a lot.

Decent product, just know two things.You need the sequential flash upgrade for the other side of the mirror. This gets its power from that upgrade. Without it you’re going to have to get creative to get power.Also, just get the amber only version unless you want to take of mirror, fish wire through truck body, and tap into the parking lights to get the white “running light” to work.

Ok

The media could not be loaded. Installed these lights to go along with the other inside mirror lights sold by the the company and removed the ugly factory orange/amber reflector. Very easy install and are plug and play if you already have the mirror side lights installed that Ruxifey sells. No drilling and no extra wiring involved. Just simply plug these lights into the two extra posts on the back side of the mirror side upgrade lights from Ruxifey and it’s as simple as that. The fit is very nice and gives the truck a more modern cleaner look. Lights are pretty bright and gives other drivers extra awareness that your turn signals or flashers are on. I would highly recommend these lights and would for sure buy them again. Just watch the YouTube videos on how to install and be careful not to break your mirror when removing it from mirror housing.

The media could not be loaded. Installed on a 2013 Ford F-150.First an foremost take your time, to remove mirror put a flathead in-between tabs and twist, starting at bottom, top tab should just pop off, there is YouTube videos on this. I didn't remove door handle either, just put a step stool or something for door panel to sit on after removal. Power for white light i used fuse #40 which is front parking lights. White light will then turn on with parking lights. I purchased rear facing leds from them also, so front would just plug into them. There wasn't enough wire for drivers side to reach passenger side to splice into power, I had some 22 gauge wire to extend it.If running wire behind door molding please put some electrical tape on section of wire that is going behind molding, my driver's side wire was cut in two when molding was pushed into place. The wire is small and the metal behind molding is sharp. And don't flip out when looking at front leds, the dot etching on mine was upside down but lights function perfectly. Their instructions are garbage, so do your research while waiting on delivery. Also I purchased puddle lights (not shown) , might as well while everything is apart. I spliced puddle light power to cabin side connector (purple wire no-stripes) and ground to bolt for mirror. Spent 4hours doing this but happy with the outcome.Update 7/4/21: right mirror front signal has lost almost half of the LEDs, look so bad now i had no choice but to remove both sides. Drivers side had no failures but left with no choice. Will not buy again due to all the work involved to install and one year later take them back out.