Stingray Hydrofoil - Starfire Hydrofoils for 40-300 hp Boats (Black) - No-Drill Engine Stabilizer Fins for Outboard/Outdrive Motors - Made in the USA

Excellent addition to my boat. It is quite easy to install. On my old Mercury outboard, I had to remove the trim tab, slide the hydrofoil on, replace the trim tab and tighten down two screws on the side of the hydrofoil.The difference was noticeable almost instantly. The boat pops right out of the water when you accelerate. There is virtually no rise in the bow as you get up to speed. I've tried it both pulling a tube and without. In both situations the boat's performance was excellent.Three cautions:1. make sure that it is perfectly straight. It's easy to have it off just a bit. It took me a couple times of adjusting the set screws before I got it right.2. Watch the set screws on the side. They need to be really tight. I didn't tighten them enough at first and then had the problem of the foil being off center by the end of the outing.3. Since putting the foil on, the boat pulls to the right. My guess is that I need to adjust the trim, but because I don't have power trim, that's a hassle and I haven't done it yet. It's not enough of a problem make me tinker with it or change my mind about the product, but I do have to keep a hand solidly on the wheel (something you should do anyway).I can't speak to the fuel savings. I don't keep close enough track on my fuel to notice any change. But the product is well worth it even if there isn't any fuel savings. It's hands down the simplest (and most noticeable) improvement I've made to my boat.

I gave the product a 3⭐️ For ease of install, could of been a five star but I don’t think most folks will have an inch lb torque wrench or red picture, I happen to so it was still easy.I gave it a 3⭐️ For sturdiness, which if I drilled for the install I think it would be a long lasting productIt did work nicely as others suggested, until of course it fell off. It was torqued and loctited to specs, yet last less than two days. $100 down the crapperIf you intend on drilling into your cavitation plate give it a whirl, if your going to “no drill install” stop right now and send 10 people you know $10 each and make a bunch of people happy rather then wasting it on a few mins of pleasure

This product was extremely easy to put on. It helped the boat to get on plane faster. Not a lot but defiantly better. Also the boat remains on plane with less power. That's going to save gas and wear on the outboard. This is well worth the money I am happy with the product.This is also made in the USA. Lifetime warranty.

First, the good: it does work. My 21 foot stern drive open bow Hurrincane got onto plane quicker with this installed. Now the bad.....you are going to want to use the install method that does not drill through your stern drive. You will think "yeah, this will work, it looks pretty stout". Your are wrong, and it will fall off. Now, since you took my advice and bought two, you can now bust out your drill and install the second one the right way and bolt it through your sterndrive. This is what I had to do after the first one disappeared in the lake. Read the other reviews and see just how many people lost theirs with the "no holes" installation.

Depending on your outboard, you may be able to get away with the no-drill install... for me though, there's no way this was a set it and forget it. Going solely with the set screws it was gonna fall off sooner or later, probably sooner.But, it's not a big deal. The best thing about this is you can slap it on and test it out with the set screws and no-drill install to see how to works on your boat. Worst case scenario it does nothing or makes it worse and all you end up with is a few scratches instead of a few holes in your outboard to fill.For me the only thing I really wanted out of this was dropping the nose of my boat (15ft aluminum deep v) before plane speed which for my boat is right around 10mph which was super annoying because almost every lake around me is no wake zoned throughout and 10mph max, so I was at a 30 degree angle almost always nearly having to stand on my seat to see what's in front of me.With this thing, now it's almost flat from 0 to plane, and it's planing at a lower speed which is even better. Haven't tested top end speed but it really doesn't matter to me and just those two things are huge quality of life improvements for my boat.Quick tip if it does work for you and you want the security of drilling and bolting it into place. Take it off and drill through the top first, then put it on and drill through the top hole so you don't have to remove your prop.

this product helped my boat a lot , great hole shot and helped my gas mileage

This product is a piece of crap. I installed it on my outboard motor. After checking all of the attaching screws and having a mechanic check behind me to make sure everything was done correctly and tight. The fin came off and was lost after a couple of uses. It scared my new engine now all I have is scratches and am out the cost. Somebody should refund my money. Use caution with this product a easy of money.

Well it worked great while it stayed on. Thought for sure it would stay on because it was so snug used my impact to do the set screws. But sure enough like everyone said before it came off. Unless you plan on doing the drill method I don’t advise getting this product. If you do worked great while it was on and did as advertised.