MonroeMagnum RV 555010 Suspension Shock Absorber and Coil Spring Assembly for Ford E-350 Super Duty

Really improved body roll and stability. Easy to install with floor jack to take weight off axle and screw jack to compress coil over shock up couple inches to bottom mount.

These are tough and built well! Very happy with our purchase!!

I just put these on my 2002 E350 Super Duty, as you can see from the pic the old shocks were shot. These new ones are high quality, and VERY BEEFY. They went on pretty easy, and gave me about an inch or so of added lift. The ride has improved tremendously, I am very happy with these new shocks. Plus the current price on Amazon is ridiculously cheap for a shock of this caliber. These are much nicer than an other brand in this price range.

I was nervous about these being too stiff for my van. I have a 2007 e350 quigley extended, and the majority of the reviews are from class c owners. I usually run with several hundred pounds in the back and a roof top tent nearly all behind the rear axle. The ride improvement was noticeable and not harsh at all. It only raised the rear around an inch. The installation was a little more difficult because of the brackets that quigley welds in to compensate for the lift blocks. After having to cut the old shocks out with a grinder, the install was a breeze. As others have said, you will need 2 jacks.

Couldn't find coilovers for this truck. Matched these up using travel, mounting style Etc. Have beefed up rear for my 3500lbs. Camper. Front was a touch low, and these stiffened roll. Decent shocks, despite the fact that they are for a Ford

Took a lot of sway on the camper drives better.

The Shocks Work, Not sure if there is any gas inside. I think its all spring. This does raise the back up maybe 3 inches. It helps but still kind of loud I guess probably leaf springs are bad. As for getting them on the vehicle, what a pain. My bolts on the old shock was rusted. The only way is to cut it. The bottom of the shock has to be jacked up, still couldn't get the bolts out of the bottom of shock without cutting it. The left shock upper bolt is 3 inches off the gas tank. I would say over 2 hours per shock. Don't need to take the tire off just get the vehicle off the ground a (3t floor jack with a piece of wood on the frame in front of tire worked for me. The leaf spring will only let the tire drop so far off the ground anyway. Once bottom bolt is out The old shock was rusted and falling apart so a pipe wrench wouldn't work. Twisting the shock off a rusted bolt. Not Happening lol The Bottom Bolts are not threaded in the shock. (who knows with Ford?) Putting the new (shock) well the bottom of the shock had metal burs that may cut your hand if trying to turn the whole shock. Both nuts at turn location was same size so (2) 3/4 wrench was needed. Putting them on 30 minutes, using a jack on the bottom to line the through bolt up. Nothing easy about this. Cut until Bolt Breaks off. Once you get the shock in the mail and out of the box take the top bolt and tight and loosen about 100 times. Your first 30 times of tightening are not going to be easy. this will probably make it easier before the shock is on the vehicle. Not a horrible job, a can do one, but it isn't easy. ford e350

#1, I think if you're only packing 1 shock rather than a set like most shocks that should be abundantly clear. They are not.#2 don't discard the old parts you remove. These don't include all the hardware you need to install them.#3 These have powerful springs and in most cases even if you jack up the RV and let the axle hang without the wheels. You'll still need to jack on the shock to collapse it a inch or 2 to connect the bottom mounting bolt. It takes some finesse.This is not a set of shocks, it's 1 shock.We'll see how they preform then we'll edit this.

great quality , sturdy build , great transaction ,